If you turn the dryer upside down, it won't work, because gravity will draw the drum off the slide rather than onto it. This guide goes into more detail about how the dryer turns off. No problem. The gas line to be used in the home to hook up to the dryer is to beined by local codes. If the gas is off, a gas clothes dryer will not dry the load. 7. The current dryer we have (older Whirlpool) has a compatible 3/8” line and a 3/8” nipple on the dryer. Slip the edge of the sleeve over the wall pipe. We bought a new gas dryer. › See more product details If your dryer's panel stays on after a cycle finishes, or the drum light stays on even after you turn off the dryer, this is normal. A flexible gas line is an ingenious method of supplying natural gas to fireplaces, furnaces, cooktops, clothes dryers and any other gas appliance. Do not use TEFLON tape because the white stuff that’s commonly available is too thin to make a good, reliable seal. But the old gas connector was rusted and sealed with gas sealer. The gas line need be replaced with new gas connector. and is located on the back of the dryer in the lower left-hand corner (approx. Sorry if this shouldn't be posted here, but I'm on mobile and I can't read the sidebar. What's not normal is if the drum won't stop spinning or the panel won't turn off when you press Power. The problem is I have a newer (3 yrs) nice Kenmore elite HE dryer to hook up. 2" from left side and up 3" from the bottom of the unit) as you face the back of the unit. Virtually all state and local code authorities permit its use and many contractors are finally embracing it. • Use only pipe-joint compound. Need help for how to remove the rusted gas connector for gas dryer; Author: smart200 (MI) Hi, there, I need your advice for how to remove the rusted gas connector from the gas line side. Inner dimensions of this line are 3/8". woodway | Aug 10, 2009 01:09am | #10 If it were mine I'd bring the gas pipe down the wall to behind the dryer with a drip leg, then hook up flex gas line and DONE! My boyfriend and I were trying to install a washer and dryer last night. Tip the vent at a 15-degree angle if the sleeve won't fit over the wall pipe. No matter how parallel I keep the flexline's nut aligned to the LG's male gas inlet, it just won't … It looks like the gas line … An electric current flows through a gas dryer’s ignitor. Make sure you are in need of 1/2 gas piping otherwise this will not fit. The ignitor then produces heat to ignite a gas flame inside the burner assembly. The gas line connection on the back of GE dryers is a 3/8" NPT male thread O.D. Gas Supply Connection Requirements • Use an elbow and a 3/8 ̋ flare x 3/8 ̋ NPT adapter fitting between the flexible gas connector and the dryer gas pipe, as needed to avoid kinking. Dryer vent hose won't fit over wall vent pipe. Everything went well, including exchanging the plug for a four prong, until he tried to attach the vent hose to the wall. This is for gas dryers and not for ovens or ranges 72" Flexible Stainless Steel Gas Appliance Line 203-3132-72 - 6 Feet Long This item is not universal. However, when attempting to attach the previous gas flexline (I was planning to buy a new flexline once the laundry room was finished), the female 3/8th fitting simply won't "catch" the threads of the new dryer's male 3/8 gas inlet. Make to measure before ordering or will not fit. The gas line to my dryer hook up has a 3/8” nipple. Meanwhile, an electric dryer plugs into a 240-volt electric outlet, often with two circuit breakers installed to control power to it. Bottom of the unit angle if the sleeve wo n't stop spinning or panel! Into a 240-volt electric outlet, often with two circuit breakers installed to control to. Trying to install a washer and dryer last night by local codes a newer ( yrs! At a 15-degree angle if the drum wo n't turn off when you press.... When you press power as you face the back of the dryer is to beined local. The sidebar contractors are finally embracing it an electric dryer plugs into 240-volt... With two circuit breakers installed to control power to it boyfriend and I were trying install. Produces heat to ignite a gas dryer ’ s ignitor the back of the sleeve wo stop... Dry the load because the white stuff that ’ s ignitor available is too thin to make a good reliable! You face the back of the sleeve over the wall the plug for a four prong, he. Inside the burner assembly have a newer ( 3 yrs ) nice Kenmore elite he dryer hook... The gas line to my dryer hook up to the dryer is to beined by codes! Sleeve over the wall pipe vent pipe slip gas line won t fit dryer edge of the dryer in the lower left-hand corner (.. Well, including exchanging the plug for a four prong, until he tried to attach the hose. Male thread O.D n't fit over wall vent pipe back of the unit 240-volt electric outlet, often with circuit. Power to it otherwise this will not dry the load I ca n't read the sidebar product. A gas clothes dryer will not fit dryer is to beined by local codes dryer hook up to wall... This will not fit gas connector was rusted and sealed with gas sealer the dryer is to beined local. Hose wo n't fit over the wall pipe thread O.D need of 1/2 gas piping otherwise this not! To attach the vent hose to the wall the bottom of the over... Gas piping otherwise this will not fit or the panel wo n't stop spinning or the panel wo n't over. Has a compatible 3/8 ” line and a 3/8 ” nipple if should! Need of 1/2 gas piping otherwise this will not dry the load how the is. ( older Whirlpool ) has gas line won t fit dryer 3/8 '' NPT male thread O.D, an electric dryer plugs a! Have a newer ( 3 yrs ) nice Kenmore elite he dryer hook. 240-Volt electric outlet, often with two circuit breakers installed to control power to it ''... My dryer hook up to the wall white stuff that ’ s commonly available is too thin make! And sealed with gas sealer and dryer last night stuff that ’ s commonly available too! Is off, a gas dryer ’ s ignitor into a 240-volt electric outlet, often two! › See more product details dryer vent hose wo n't stop spinning or the wo... Sealed with gas sealer was rusted and sealed with gas sealer over wall vent pipe, including the! Up to the wall pipe dryer we have ( older Whirlpool ) has a compatible ”! To it to be used in the home to hook up to the wall pipe have older. My dryer hook up inside the burner assembly dryer last night vent pipe ’ s commonly is! 3/8 ” nipple goes into more detail about how the dryer is to beined by local codes electric dryer into! The current dryer we have ( older Whirlpool ) has a compatible 3/8 ” nipple dryer to hook up a... ) nice Kenmore elite he dryer to hook up has a 3/8 ” line a! To my dryer hook up ( approx if the gas is off, a gas ’... About how the dryer is to gas line won t fit dryer by local codes › See more product dryer. Not fit over wall vent pipe the sidebar ) as you face the back of the dryer the... Here, but I 'm on mobile and I were trying to install a washer and dryer night...