Break the designated clips to separate the 2 parts of the tub. Find the drain filter. Bend the wire stepping back 6-7 sm from each end– you’ll get a kind of hook. Sometimes coins, bra underwires and other metal objects come loose in the wash and become stuck between the tub and the drum. Let us consider the causes of failures. In fact, it is not difficult; you still need to make an effort. If you … The washer won’t heat the water during a washing cycle. It either … In this case, contact the customer service department on 1300 369 744. Next, unscrew the pump cover and fluff filter. Watch our video with an instruction and tips on how to clean the filter in your Bosch washing machine… I could unscrew it and pull out slightly anticlockwise to drain … The contacts of the pump have burnt out or oxidized. Remove the tub with the drum by unscrewing the spring. The Bosch Axxis washing machine has a safety lock feature that automatically disables the door from opening while the washing cycle is in process to prevent opening the washer and causing water spillage. If you have not identified the failure and you do not know how to repair your washing machine, consult a professional. Check the “AQUA-STOP” filter. The solution then is to remove the pump from the machine and then detach the motor from the pump housing. If you have an older top-loading washer, your filter will also be in the bottom right-hand corner of the machine. This is a 4kg washer with a couple of really long 7kg washes ! Check the drain hose (it can be bent or creased). You need these for product registration and booking your repair service. Install it in place. Unscrew the water supply and lay a towel under it. There is no water in the water system, the pressure is low. 200 Ohms is normal. If the filter cap is stuck fast it may be due to limescale build up, not a coin or clip. To make this hook get a 30-centimeter piece of 3 mm steel wire. For front-loading machines, the filter will be in the bottom right corner on the outside of the washer. Washing Machine Tub Seal and Bearing Kit. ... Or there’s something stuck … The machine also won’t spin if the lid switch is faulty, the drive belt is broken, or the door won’t close. First, unplug the washing machine and make sure that there is no power to it. Will Not Spin and/or Agitate. - Answered by a verified UK Appliance Technician We use cookies to give you the … Install the new part in place of the old one. Turn the filter cover to the left and get it out. Remove the heater by moving it slowly to the right and to the left and pulling out. After removing the module, lay it on the frame or hang on a special hook. In this case, contact the customer service department on 1300 369 744. Put the shrink (shrinking tube) on the wire. It does not require special knowledge or efforts. First turn the appliance off and disconnect the power, then turn the water supply off. If you venture to do it, do not remove all the wires from the electronic module, because you may not put them all in place eventually. Washing Machine Pump Filters. Check the resistance of the winding of the pump. Watch our video on how to clean the drain pump in your Bosch washing machine. If the reading is “1”, the heating element is broken and needs to be replaced. In case of the water level switch failure, follow the recommendations to replace it: If the heater has fulfilled its service life, has overheated and burned out or the limescale has formed, the element needs replacement. Set the mode to measure resistance (in ohms) on the tester. If the impeller can’t be turned, something could have become jammed in the pump. DP did this for some friends of ours with a Bosch… This video will show you how to gain access to the pump … It is located at the bottom of the machine under the front panel (put the machine on its side to reach it) or behind the door of the small maintenance hatch. If the impeller can’t be turned, something could have become jammed in it. In the spirit of the maintenance wash threads, I gave my washing machine a clean yesterday, but the little round filter door at the bottom was stuck. If you are not sure whether the heater is broken, check it with a tester. Find the drain filter. If you've forgotten where you put the manual that came with your appliance, you can download it online. Hang the control board on it. To remove the lid remove 2 bolts. Remove the bottom panel by removing the screw near the filter and the screws at the bottom of the panel. View information about the cookies we use, [global.cookielaw.txt.checkbox.performance], [global.cookielaw.txt.checkbox.targeting], [global.cookielaw.txt.checkbox.thirdparty], Freestanding fridges without freezer section, Stacking kits for washing machines and dryers, Nets and accessories for delicated clothes, For bean-to-cup coffee machines and thermos flasks, Active carbon filters for extractor hoods. First, unplug the washing machine and make sure that there is no power to it. Due to their high quality and many innovative technologies introduced. Identify your appliance to find your E-Nr (model) and FD (producion) number. Reinstall the elements in the reverse order. Clean the filter and wash it under the tap. Clean the filter and wash … In this case, contact the customer service department on 1300 369 744. Let’s replace the heater: To carry out this difficult task you need to disassemble the washer almost completely. Now open the service flap and let off the water through the pipe. If the pump is all right, the impeller turns easily in all directions. But in this case, it is necessary to leave some rags on the floor or put a basin under the washing machine. If the impeller can’t be turned, something could have become jammed in it. Watch our video with an instruction and tips on how to clean the filter in your Bosch washing machine. Find your washing machine filter. The shock absorbers are floppy or broken. Now open the service flap and let off the water through the pipe. If you have an item stuck in your washing machine there are only really only two ways to obtain access to the drum .